Our form-in-place “Ring Gasket on a Roll” is one of the most versatile and widely used gasket materials available. Exceptional sealing properties and conformability, with resistance to creep and cold flow make it an ideal choice for many bolted assemblies such as standard flanges, man ways, tank covers, ducting, heat exchangers and many others.
UHF Joint Sealant Flyer
Product Description
TEMPERATURE RANGE:
-450°F (-268°C) to +600°F (+315°C)
PRESSURE RANGE:
Full Vacuum to 3000 psi (20.7MPa/207 Bar)
CHEMICAL COMPATIBILITY:
100% expanded virgin PTFE
0 – 14 pH
FDA COMPLIANT:
Meets FDA 21CFR177.1550
LOW CREEP AND COLD FLOW
NON-TOXIC, SILICONE-FREE
NON-CONTAMINATING
NON-PARTICULATING
NON-AGING IN SERVICE
“RING GASKET ON A ROLL”
INERTEX® UHF Joint Sealant’s low-torque-to-seal properties make it a successful solution for a wide range of equipment including tank covers, access doors, high temperature air and exhaust ducting, compressors, and heat exchangers to name but a few. Simple to use and easy to install, UHF joint sealant delivers superior performance in a cost effective form and it is commonly referred to as “Ring Gasket on a Roll”.
- Wide pressure and temperature range
- Unsurpassed chemical compatibility
- Excellent creep and cold flow resistance
- Will not harden or deteriorate with age
- Low coefficient of friction allows easy removal
- Easily conforms to damaged or pitted flanges
- Low compressive load to seal
- Wide adhesive strip for easy installation for all shapes, vertical or horizontal
- Professional engineering support
UHF JOINT SEALANT SIZES:
| STANDARD WIDTHS | SPOOL LENGTHS (FT/SPOOL) |
|---|---|
| 1 MM | 100, 1000 |
| 1/8″ | 100, 1000 |
| 3/16″ | 75, 750 |
| 1/4″ | 50, 100, 500 |
| 3/8″ | 25, 50, 250 |
| 1/2″ | 15, 30, 150 |
| 5/8″ | 15, 30, 150 |
| 3/4″ | 15, 30, 50, 100 |
| 1″ | 15, 30, 75 |
| 2″ | 39 |
UHF JOINT SEALANT SIZE SELECTION REFERENCE
| 150-300 LB. ANSI FLANGES | RECOMMENDED SIZE | SEALING CONTACT AREA WIDTH | RECOMMENDED SIZE |
|---|---|---|---|
| 1/2″ – 3/4″ | 1/8″ | 1/8″ – 1/4″ | 1/8″ |
| 1 – 1.5″ | 3/16″ | 5/16″ – 3/8″ | 3/16″ |
| 2″ – 3.5″ | 1/4″ | 7/16″ – 5/8″ | 1/4″ |
| 4″ – 6″ | 3/8″ | 3/4″ – 1″ | 3/8″ |
| 8″ – 16″ | 1/2″ | 1.125″ – 1.5″ | 1/2″ |
| 18″ – 20″ | 5/8″ | 1.625″ – 2″ | 5/8″ |
| 24″ – 36″ | 3/4″ | 2″ – 2.5″ | 3/4″ |
| 35″ – 60″ | 1″ | 2.5″ – 3″ | 1″ |
| 60″+ | 2″ | 3″+ | 2″ |
| RULE OF THUMB: 1/2 to 1/3 the width of gasket contact area from bolt hole to flange ID | |||